Once added to Home Assistant you can configure different settings for your R PRO-1. Use the tabs below to see what each entity does, grouped the same way Home Assistant displays them.
The R PRO-1 pairs two radars: an LD2450 that tracks the position of up to three targets and reports zone occupancy, and an LD2412 that handles presence and per-gate sensitivity tuning. It also carries an LTR390 light sensor and an optional SCD40 CO₂ module.
How often readings update
The Default Update column is how often each entity refreshes. Radar entities update in real time as targets move. The SCD40 and LTR390 sensors report every 60s.
Control
What it does
RGB Light
Four RGB Neopixel LEDs. Click the light bulb or color wheel to change the color. Use the toggle to turn them on or off.
Calibrate SCD40 To 420ppm
Forces a fresh-air calibration of the SCD40 CO₂ sensor to the outdoor baseline (about 420 ppm). Run it outdoors or next to an open window. Only needed when CO2 Auto Calibration is off.
Combined occupancy: shows Detected when either the LD2450 or the LD2412 radar sees a target, and Clear when neither does. Use this entity for automations and dashboards instead of the individual radar presence sensors. It comes with R PRO-1 firmware newer than 26.3.2.1. On 26.3.2.1 and earlier, use LD2412 Presence for the whole room, or LD2450 Presence on an R PRO-1 without the LD2412.
Restarts the device. Helpful for troubleshooting or refreshing the connection.
Firmware Type
WiFi / Ethernet
Switches between the Wi-Fi and Ethernet firmware without re-flashing. After picking the firmware you want, press Firmware Update to apply it.
Reduce DB Reporting
Off
Filters several entities so they only report when a threshold is met, using less Wi-Fi airtime and less Home Assistant database space.
SCD40 Temperature Offset
18.86 °C
Calibration offset for the SCD40 temperature reading. Disabled by default.
SCD40 Humidity Offset
0 %
Calibration offset for the SCD40 humidity reading. Disabled by default.
CO2 Auto Calibration
On
Keeps the SCD40 CO₂ sensor calibrated automatically. The sensor assumes it sees fresh air (about 420 ppm) at least once a week and corrects its baseline to match. Turn it off if the device sits in a space that rarely gets fresh air, then calibrate manually with Calibrate SCD40 To 420ppm every 1 to 2 years.
Toggles the LD2450's Bluetooth so you can connect with the HLK Radartool phone app for tuning. Turn it back off when finished.
LD2450 Multi Target Tracking
from module
Turns multi-target tracking on or off. Initial state is read from the LD2450 at boot. Disabled by default.
LD2450 Timeout
—
Seconds the LD2450 presence stays detected after the target is lost.
LD2450 Zone Type
Disabled
Zone detection mode: Disabled, Detection (only detect targets inside the zone), or Filter (exclude the zone from detection). With Detection and no zones set, the radar detects nobody, so keep Disabled unless you use the radar's own zones.
LD2450 Zone-1 / Zone-2 / Zone-3 X1, X2
—
Start and end X coordinates of the zone in mm (-4860 left to 4860 right).
LD2450 Zone-1 / Zone-2 / Zone-3 Y1, Y2
—
Start and end Y coordinates of the zone in mm (0 to 7560).
LD2450 Factory Reset
—
Resets the LD2450 radar module to its factory settings.
LD2450 Baud rate
from module
Serial baud rate the LD2450 uses to talk to the R PRO-1 (default 256000). Disabled by default; no need to change.
Entity
Default Update
What it shows
Apollo Firmware Version
on boot
The Apollo firmware build installed on the device (for example, 26.3.2.1).
ESPHome Version
on boot
The ESPHome version the firmware was compiled with.
Firmware Update
—
Shows whether a firmware update is available and lets you update from inside Home Assistant.
IP Address
on connect
The device's IP address on your network (Wi-Fi firmware).
Online
on change
Connection status of the device to Home Assistant.
ESP Temperature
60s
Internal temperature of the ESP32 chip. Runs warmer than the room because of the processor and Wi-Fi radio. Disabled by default.
Uptime
60s
How long the device has been running since its last reboot.
LD2412 Dynamic Background Correction Status
real-time
Whether the LD2412 is running dynamic background correction.
LD2412 Out Pin
real-time
State of the LD2412 hardware output pin. Disabled by default.
LD2412 Firmware
on boot
Firmware version installed on the LD2412 radar module. Disabled by default.
LD2412 BT MAC
on boot
Bluetooth MAC address of the LD2412 radar module. Disabled by default.
LD2412 g00 to g13 move energy
real-time
Live move energy for each gate (g00 to g13), used when tuning with Engineering Mode.
LD2412 g00 to g13 still energy
real-time
Live still energy for each gate (g00 to g13), used when tuning with Engineering Mode.
LD2412 Query params
—
Queries the LD2412's current parameters for debugging or advanced setup.
LD2412 Restart
—
Restarts the LD2412 radar module.
LD2412 Start Dynamic Background Correction
—
Kicks off a dynamic background correction pass on the LD2412.
LD2450 Firmware
on boot
Firmware version installed on the LD2450 radar module. Disabled by default.
LD2450 BT MAC
on boot
Bluetooth MAC address of the LD2450 radar module. Disabled by default.