Advanced Search
Search Results
182 total results found
Manually Uploading Code Through ESPHome
If your device becomes unresponsive and you've exhausted the other troubleshooting methods you can upload a fresh set of firmware by following the below guide. The utility does need to be run from Chrome or Edge. If your device has already been connected to H...
Putting The MSR-2 In Boot Mode
This will cover how to put the MSR-2 into boot mode. Sometimes, this is needed to upload new firmware if the device is struggling.Boot Button Only Please look at the photo below to help access the boot button through the top of the case Use a pin to press ...
Smart Home Scene MSR-2 Review
Apollo MSR-2 Review: The Smallest Presence Sensor Ever Made
Zone Configuration Using Home Assistant
Disclaimer: Currently having issues saving the zones after restarting the device when using this method. It is recommended to use the HLKRadarTool App Zone Configuration Guide.You will need to have HACS and Plotly installed to make it easier to visualize the z...
Zone Configuration Using HLKRadarTool App
1. Download the HLKRadarTool app for either Android or Apple2. Ensure the mmWave radar you want to configure has Radar Control Bluetooth turned on. Home Assistant > Settings > Devices & services > ESPHome Devices > Select Device > Scroll down and toggle on Rad...
Simon Says Home Assistant MSR-2 Review
The Apollo MSR2 Presence Sensor is now even smaller!
How To Add Temp And Humidity From SCD40
1. Navigate to the ESPHome addon 2. Select the Edit button under the desired device 3. Insert your code (The example below is for our AIR-1 SEN55 sensor but this applies to MSR-1/2, MTR or any sensor with the CO2 module) sensor: - platform: scd...
Home Tech Innovations MSR-2 Review
Setup MSR-2 in 3 EASY Steps!
Wi-Fi Disconnecting
Try a couple of different power cord and power brick combinations - this matters a lot more than you'd think! Check to see if the sensor's hotspot is showing up. (this means it is not connected to a network) Check the router's connected devices - the devic...
Hands On Katie AIR-1 Review
Best Air Quality Sensor? I pull apart the Apollo AIR-1… and find four great company traits....
Getting Started With Apollo Odroid Flashed With Home Assistant (Odroid M1S)
This guide will walk you through setting up your Apollo Home Assistant Hub (link) Plug your hub into the wall with the included power adapter Attach the included ethernet cable from the hub to an available ethernet port on your router From a phone or co...
Adjusting Wifi Power Save
The ESP chips produce a significant amount of energy constantly using wifi. Here is how to adjust the wifi power save mode In ESPHome's addon, click on "Edit" for the sensor you want to adjust Add the code to adjust the power wifi: ss...
Teardown and Reassembly of the MTR-1
This will cover how to take apart and reassemble the MTR-1 device. This is useful if you are replacing components or to inspect if the mmwave sensor (LD2450) is seated properly. Sometimes during shipping, this can become loose and cause issues with the accurac...
Smart Home Australia MSR-2 Review
Apollo MSR2 Radar Motion Sensor - Small just got tiny !!
How To Use The Apollo GPIO Header To Control An LED Strip
This tutorial will guide you through setting up one of our MSR-2 devices (works with any mezzanine port on any Apollo Device) with the optional $4.99 GPIO Header which adds pins for you to easily add functionality to your device! In this tutorial, however, w...
How To Use The Apollo GPIO Header To Control An LED Strip
This tutorial will guide you through setting up one of our MSR-2 devices (works with any mezzanine port on any Apollo Device) with the optional $4.99 GPIO Header which adds pins for you to easily add functionality to your device! In this tutorial, however, w...
How To Use The Apollo GPIO Header To Control An LED Strip
This tutorial will guide you through setting up one of our MSR-2 devices (works with any mezzanine port on any Apollo Device) with the optional $4.99 GPIO Header which adds pins for you to easily add functionality to your device! In this tutorial, however, w...
How To Use The Apollo GPIO Header To Control An LED Strip
This tutorial will guide you through setting up one of our MSR-2 devices (works with any mezzanine port on any Apollo Device) with the optional $4.99 GPIO Header which adds pins for you to easily add functionality to your device! In this tutorial, however, w...
Michael Leen MSR-2 Review
Don’t Be Fooled By Its Size: Apollo MSR-2 mmWave Multisensor
Smart Home Australia MTR-1 Review
NEW Apollo MTR-1: mmWare sensor: Review, Home Assistant installation, dashboard and conclusion