Skip to main content

Recently Updated Pages

mmWave Comparison

General Sensor Comparisons

<table>  <thead>    <tr>      <th></th>      <th>Apollo MSR-1</th>      <th>Apollo MSR-2</th>    ...

Updated 3 days ago by justin@apolloautomation.cloud

How To Add Temp And Humidity From SCD40

General Setup

1. Navigate to the ESPHome addon    2. Select the Edit button under the desired device    3. I...

Updated 4 days ago by Trevor

mmWave Presence Sensor Comparison

MSR-2 Additional Info

Link to Excel file: mmWave Presence Sensor Excel Spreadsheet

Updated 1 week ago by justin@apolloautomation.cloud

Reset Wi-Fi Credentials

AIR-1 Troubleshooting

Plug the device into power Long press the Boot button for 10 seconds The Wi-Fi credentials sh...

Updated 1 week ago by justin@apolloautomation.cloud

Manually Uploading Code Through ESPHome

MTR-1 Troubleshooting

If your device becomes unresponsive and you've exhausted the other troubleshooting methods you ca...

Updated 1 week ago by justin@apolloautomation.cloud

Putting The MTR-1 In Boot Mode

MTR-1 Troubleshooting

This will cover how to put the MTR-1 into boot mode. This is sometimes needed for uploading new f...

Updated 1 week ago by justin@apolloautomation.cloud

Simon Says Home Assistant MSR-2 Review

MSR-2 MSR-2 Reviews

Updated 1 week ago by justin@apolloautomation.cloud

Reducing LD2410 Log Entries In Home Assistant

MSR-2 Additional Info

Open your Home Assistant config.yaml Add in this code but use your MSR-2's name logbook: ...

Updated 1 week ago by justin@apolloautomation.cloud

Adding CO2 To MSR-2

MSR-2 Additional Info

This is for the MSR-1 but it is very similar to the MSR-2.1. Unplug your MSR-2 from power and rem...

Updated 1 week ago by justin@apolloautomation.cloud

How To Change The Update Frequency Of Sensors

MSR-2 Setup

How To Change The Update Frequency Of Sensors

Updated 1 week ago by justin@apolloautomation.cloud

Manually Uploading Code Through ESPHome

MSR-2 Troubleshooting

If your device becomes unresponsive and you've exhausted the other troubleshooting methods you ca...

Updated 1 week ago by justin@apolloautomation.cloud

Putting The MSR-2 In Boot Mode

MSR-2 Troubleshooting

This will cover how to put the MSR-2 into boot mode. This is sometimes needed for uploading new f...

Updated 1 week ago by justin@apolloautomation.cloud

MSR-2 + Alarmo Home Security Install

MSR-2 Examples

My grandmother wanted a security system that would alert her when there was movement in her home ...

Updated 1 week ago by justin@apolloautomation.cloud

MSR-2 Examples From GitHub

MSR-2 Examples

MSR-2 Examples from GitHub

Updated 1 week ago by justin@apolloautomation.cloud

MSR-2 Automation Guide

MSR-2 Examples

Updated 1 week ago by justin@apolloautomation.cloud

Using MSR-2 Buzzer

MSR-2 Examples

This guide will walk you through using the buzzer on your MSR-2. You can also call the below se...

Updated 1 week ago by justin@apolloautomation.cloud

MSR-2 Home Assistant Dashboard Examples

MSR-2 Examples

Radar Scatter Plot With Apex Charts For MSR-2 type: custom:apexcharts-card header: show: t...

Updated 1 week ago by justin@apolloautomation.cloud

How To Tune mmWave Using Home Assistant

MSR-2 Calibrating And Updating

If you're experiencing false triggers, we recommend using Radar Engineering Mode (REM) to monitor...

Updated 1 week ago by justin@apolloautomation.cloud

MSR-2 Temperature & Humidity Offsets

MSR-2 Calibrating And Updating

DPS310 & SCD40 Sensors: Overcoming Temperature & Humidity Reading Challenges The DPS310 and SCD4...

Updated 1 week ago by justin@apolloautomation.cloud

CO2 Calibration For MSR-2

MSR-2 Calibrating And Updating

Please refer to the General CO2 Calibration article

Updated 1 week ago by justin@apolloautomation.cloud