Advanced Search
Search Results
182 total results found
Putting The MTR-1 In Boot Mode
This will cover how to put the MTR-1 into boot mode. Sometimes, this is needed to upload new firmware if the device is struggling.Boot Button Only See the photo below to help access the boot button through the top of the case Use a pin to press and hold th...
Simon Says Home Assistant MTR-1 Review
New Apollo MTR-1 Multi-target Radar For Home Assistant (ld2450)
Getting Started
Please refer to the general getting started article
Sensor Definitions
Once added to Home Assistant you can configure different settings for your sensor. Below is what each setting does. Controls RGB Light A RGB Neopixel. Click on the light bulb to change the color. Click on the toggle to turn on or off Sensors C...
Bluetooth Tracking with MSR-2
Please refer to the general Bluetooth tracking article
General Tips
MSR-2 Light Sensor (LTR-390UV) When mounting the MSR-2 be sure to position the device so that the two large holes are not covered This allows more light to enter and will ensure better accuracy The onboard RGB LED will trigger the light sensor ...
How To Change The Update Frequency Of Sensors
How To Change The Update Frequency Of Sensors
Updating MSR-2 Firmware
Please refer to the general firmware update article
How To Tune mmWave Using Home Assistant
If you're experiencing false triggers, we recommend using Radar Engineering Mode (REM) to monitor the gate energy and adjust the gate threshold to eliminate them.Here is a quick introduction video of the ld2410b gates and zones. Here is a video of how to tune...
How To Tune mmWave Using HLKRadarTool
Auto-Calibration (Average, Maximum, and Intelligent)1. Download the HLKRadarTool app for either Android or Apple The default password to connect to the HLKRadarTool is HiLink 2. Ensure the mmWave radar you want to tune has Radar Control Bluetooth turned ...
MSR-2 Temperature & Humidity Offsets
Simple Offsets for Temperature and Humidity: Please add these to the bottom of your esphome yaml for your device then click save and install. Once you are finished, you will have two new boxes inside the home assistant esphome integration device page for your...
CO2 Calibration For MSR-2
Please refer to the General CO2 Calibration article
MSR-2 Home Assistant Dashboard Examples
Radar Scatter Plot With Apex Charts For MSR-2 type: custom:apexcharts-card header: show: true title: MSR-1 Radar Distance show_states: true colorize_states: true apex_config: legend: position: top horizontalAlign: center offs...
Using MSR-2 Buzzer
This guide will walk you through using the buzzer on your MSR-2. You can also use the "action" in an automation in Home Assistant. Open Home Assistant and navigate to developer tools in the bottom left 2. Click on services 3. Choose your MSR-2's...
MSR-2 Automation Guide
MSR-2 Examples From GitHub
MSR-2 Examples from GitHub
MSR-2 + Alarmo Home Security Install
My grandmother wanted a security system that would alert her when there was movement in her home after she had gone to bed. So, I set up three of our Apollo Automation mmWave sensors. These devices, plus the Alarmo add-on, quickly and easily allowed me to inst...
mmWave Presence Sensor Comparison
Column1 Apollo MSR-1 Apollo MSR-2 Everything Presence One Kit Everything Presence Lite Kit Screek Human Sensor 1U Screek Human Sensor 2A Aqara FP1 Aqara FP2 Apollo MTR-1 Price (USD) $ 34.99 $ 34.99 $ 78.00 $ 37.00 $ 25.99 $ 29.99 $...
Adding CO2 To MSR-2
This is for the MSR-1 but it is very similar to the MSR-2.1. Unplug your MSR-2 from power and remove the back 2. Remove the board from the case and orientate it like the below image. In the bottom right there is a black connector. There is an x in the lower...
Reducing LD2410 Log Entries In Home Assistant
Open your Home Assistant configuration.yaml Add this code to the very bottom but use the entity name of your MSR-2 logbook: exclude: entities: - binary_sensor.hallway_motion_home_security_motion_detection Check Configuration in Home Assis...